一、骨架網：

1、 Skeleton network:

骨架網的外觀質量應符合下列要求：

The appearance quality of the skeleton net should meet the following requirements:

A。在100mm長一段骨架網繩內有三股以上的紗（或線）斷裂，則該段骨架網繩被認為是斷裂。每片骨架網上網繩斷裂應不多于4處，且同一網目或相鄰網目內應不出現1處以上的網繩斷裂。

A. If there are more than three strands of yarn (or thread) broken within a 100mm long section of the skeleton mesh rope, the section of the skeleton mesh rope is considered broken. The number of wire rope breaks on each skeleton mesh should not exceed 4, and there should be no more than 1 wire rope break within the same mesh or adjacent mesh.

B。網繩打結（網目結點除外）或松捻，在每片骨架網上應不多于8處，且同一網目相鄰網目內應不出現1處以上打結或松捻。

B. The knot or loose twist of the mesh rope (excluding mesh nodes) should not exceed 8 places on each skeleton mesh, and there should be no more than 1 knot or loose twist within adjacent mesh of the same mesh.

二、偽裝網面：

2、 Disguise mesh surface:

偽裝網面的外觀質量應符合下列要求：

The appearance quality of the camouflage mesh surface should meet the following requirements:

A。不應有寬度大于3mm、長度大于500mm的漏底、色條和色檔（10mm寬布包邊除外）；

A. There should be no bottom leakage, color strips, or color swatches with a width greater than 3mm and a length greater than 500mm (except for 10mm wide cloth edging);

B。寬度為1~3mm、長度為（100~500）mm的漏底、色條和色檔在2㎡的面積內不多于1條；

B. There should be no more than one bottom drain, color bar, and color bar with a width of 1-3mm and a length of (100-500) mm within an area of 2 square meters;

C。偽裝網面的表面不應有面積大于20m㎡的氣泡。

C. The surface of the camouflage net should not have bubbles with an area greater than 20 square meters.

三、熱隔絕層：

3、 Thermal insulation layer:

熱隔絕層的外觀質量應符合下列要求：

The appearance quality of the thermal insulation layer should meet the following requirements:

A。熱隔絕層內外表面的涂層不應有寬度大于5mm、長度大于500mm的漏底、色條、和色檔，寬度為（1~5）mm的漏底、色條、和色檔在2㎡的面積內應不多于1條；

A. The coating on the inner and outer surfaces of the thermal insulation layer should not have any leaks, color bars, or color bars with a width greater than 5mm and a length greater than 500mm. There should be no more than one leak, color bar, or color bar with a width of (1-5) mm within an area of 2 square meters;

B。熱隔絕層表面不應有面積大于20m㎡的氣泡；

B. The surface of the thermal insulation layer should not have bubbles with an area greater than 20m 2;

C。不應有面積大于眼瞼孔兩倍的破洞和長度大于15mm的裂縫；

C. There should be no holes larger than twice the area of the eyelids and cracks longer than 15mm;

D。眼瞼聯結部撕裂30%以上，則該眼瞼被認為是斷裂；眼瞼斷裂的眼瞼孔數量應不大于總眼瞼孔數量的5%；

D. If the tear in the eyelid junction is more than 30%, the eyelid is considered to be broken; The number of eyelids with broken eyelids should not exceed 5% of the total number of eyelids;

E。固定繩不應有3股以上的斷線。

E. The fixed rope should not have more than 3 broken strands.

四、偽裝網整體：

4、 Disguise net as a whole:

偽裝網整體的外觀質量應符合下列要求：

The overall appearance quality of the camouflage net should meet the following requirements:

A。偽裝網的各種顏色應符合技術文件或合同的要求；

A. The various colors of the camouflage net should meet the requirements of technical documents or contracts;

B。切花形式應符合技術文件的要求，切口長度有30%以上未切開則被認為是不合格；

B. The cutting form should meet the requirements of the technical documents. If more than 30% of the cutting length is not cut, it is considered unqualified;

C。裝飾片應該技術文件的規定進行綁扎，每片偽裝網上漏綁處應不多于50處，且不能有連續的漏綁；

C. Decorative pieces should be bound according to the technical documents, and there should be no more than 50 missing binding points on each piece of camouflage net, and there should be no continuous missing binding;

D。邊繩上不允許3股以上的線共斷裂處；

D. No more than 3 strands of wire are allowed to break together on the edge rope;

E。加強繩上不允許有3股的線共斷裂處；

E. It is not allowed to have three strands of broken wires on the reinforcing rope;

F。四角的加強布應按技術文件進行縫制。

F. The reinforcing fabric at the four corners should be sewn according to the technical documents.